Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
  RegisterRegister  LoginLogin
PowerHome General
 PowerHome Messageboard : PowerHome General
Subject Topic: W800RF32 Extended Data Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
mdsmith
Newbie
Newbie


Joined: April 24 2019
Location: United States
Online Status: Offline
Posts: 4
Posted: May 07 2019 at 13:27 | IP Logged Quote mdsmith

I am using the W800RF32 device. Using a Window/door switch the W800 see the incoming data when the door is opened (PH Stat). Using the macro ph_multix ("EXT",1,1) to obtain the data, does not see the data.

Macro-
Seq      Command data ID Value Formula    
---------------------------------------------------------
10 Set   Global   DOOR   ;  ph_multix("E XT",1,1)
20 Set System   [LOCAL1]   ph_multix("EXT",1,1)
30 Message Box No        ph_multix( "A",1,1)
40 Message Box No        ph_multix( "EXT",1,1)

Ph Stat show -
Time   Stamp     Typ e   Details
---------------------------------------------------------
May 07 Incoming x10 Incoming Extended RF received on Controller W800RF Housecode: A Unit:Command: off

May 07 Incoming X10 Incoming Extended RF received on Controller W800RF Unit: 245 Data 129


1st Message Box shows A0102
2nd Message Box shows 00000

Am I using the ph_multix("EXT",1,1) correctly? Is there any of ph_ command I can use to obtain the data?

Michael


Edited by mdsmith - May 08 2019 at 08:32
Back to Top View mdsmith's Profile Search for other posts by mdsmith
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2867
Posted: May 07 2019 at 19:04 | IP Logged Quote TonyNo

I don't think you want multix. That's for combining multiple X-10 transmissions into unique actions.

For my window/door switches, I have a trigger set up for "X10 RF in Ext" and All Data and the data gets loaded into [TEMP3] (ID/address?) and [TEMP4] (data), then I check those.
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
mdsmith
Newbie
Newbie


Joined: April 24 2019
Location: United States
Online Status: Offline
Posts: 4
Posted: May 07 2019 at 19:33 | IP Logged Quote mdsmith

Wow, thank you, I'll try that. I need time to try this
and play around with it, not sure I understand how your
procedure works or how to implement it. I'll get back to
you and let you know. Thanks again!

Michael
Back to Top View mdsmith's Profile Search for other posts by mdsmith
 
mdsmith
Newbie
Newbie


Joined: April 24 2019
Location: United States
Online Status: Offline
Posts: 4
Posted: May 08 2019 at 08:12 | IP Logged Quote mdsmith

With the information you provided I was able to figure it
out. Fantastic! This is so cool. Using the Message Box
and TEMP variables (" [TEMP1]"+ " [TEMP2]"+ " [TEMP3]"+"
[TEMP4]"),I know which door/window is open or closed.
Thank you so much for your help!

PowerHome ROCKS!

Michael

Edited by mdsmith - May 08 2019 at 18:45
Back to Top View mdsmith's Profile Search for other posts by mdsmith
 
HarrySaw
Newbie
Newbie
Avatar

Joined: May 24 2019
Location: United States
Online Status: Offline
Posts: 4
Posted: May 29 2019 at 16:46 | IP Logged Quote HarrySaw

Thanks for the recommendations, fellas!
Back to Top View HarrySaw's Profile Search for other posts by HarrySaw
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum